---
title: "Methodology and Sources – DeckTally"
description: "How every DeckTally number is computed, tested and checked, who checks it, and the full list of codes, guides and standards the calculators cite."
author: "Hassan Razeen"
datePublished: "2026-10-27"
dateModified: "2026-11-16"
image: "https://decktally.com/og.png"
url: "https://decktally.com/methodology/"
---

# Methodology and sources

Every number on DeckTally is either arithmetic the page shows you, or a figure copied from a published code, guide or standard that the page names. This page says how that works, who checks it, and lists every publication the site cites.

## How the numbers are made

-   **One engine per calculator.** Each of the 10 calculators is a small, pure function. The page you read, the results that update as you type, the worked example, the FAQ answers and the size tables all call the same function, so none of them can drift from the others.
-   **Working shown.** Every result carries the sum that produced it, in your own numbers, so you can check it with a pencil or against a supplier's quote.
-   **Figures that are not computed are cited.** Joist spans, waste allowances, fastener schedules, stair and guard limits and lumber sizes are copied from the publications below and quoted next to the result that uses them. Where a figure in a guide is a drawing rather than text, it was read from the drawing and the figure number is given.
-   **No prices and no coverage rates.** Lumber prices and stain coverage change by region, product and season, so the cost and stain calculators take them from you. The worked examples that show such a number say so.
-   **Tested before every release.** Each engine has unit tests that pin its worked example and its edge cases, every cited source is tested to be a secure, unique address, the built pages are checked for the headings and structured data they must carry, and the site is not deployed unless every check passes.

## Who checks it

[Hassan Razeen](https://decktally.com/about/) builds the calculators and checks every quoted figure against the publication it cites before it goes live. There is no separate review board: this is one person's site, and it says so. Corrections are logged on the [About page](https://decktally.com/about/#corrections); the latest is dated 2026-11-16. Found a mistake? [Send a correction](https://decktally.com/contact/).

## Every source the site cites

9 publications from 7 publishers. Each calculator page repeats the ones it uses next to its results.

-   **International Code Council**, [2021 International Residential Code, Table R507.7 (maximum joist spacing for wood decking)](https://codes.iccsafe.org/content/IRC2021P2/chapter-5-floors)
    -   Deck lumber calculator: Joist spacing allowed for 1.25-inch and 2-inch wood decking, laid across the joists or diagonally. Local amendments can differ, so check your building department.
    -   Deck joist calculator (2021 International Residential Code, Section R507.6 and Table R507.6 (deck joist spans)): The same joist spans as adopted into the model code. Local amendments can differ, so check your building department.
    -   Deck beam calculator (2021 International Residential Code, Section R507.5 (deck beams)): The code section for deck beam spans and bearing. Local amendments can differ, so check your building department.
    -   Deck footing calculator (2021 International Residential Code, Sections R507.3 (deck footings) and R403 (footings)): The code sections for deck footings, which the guide cites as R403. Local amendments, soil values and frost depths differ, so check your building department.
-   **Trex Company**, [Trex Decking Installation Guide (2022)](https://www.trex.com/content/dam/trex/literature/product-installation/2022-trex-decking-installation-guide.pdf)
    -   Deck lumber calculator: Joist spacing for composite boards (16 inches residential, 12 inches commercial, 4 inches less at a 45-degree angle) and the minimum 3/16-inch gap between boards.
    -   Deck screw calculator: Recommends two screws per joist when face-screwing composite boards; requires hidden fasteners at every joist; starts the first board on a starter clip and suggests a hidden-fastener screw and plug for the last board.
-   **American Wood Council**, [DCA 6: Prescriptive Residential Wood Deck Construction Guide (2015)](https://awc.org/wp-content/uploads/2021/12/AWC-DCA62015-DeckGuide-1804.pdf)
    -   Deck lumber calculator: Two screws or nails where each board crosses a joist, boards gapped about 1/8 inch, and each length of decking resting on at least three joists.
    -   Deck joist calculator (DCA 6: Prescriptive Residential Wood Deck Construction Guide (2015), Table 2 and the joist and hanger sections): Every allowable span and overhang in the table (40 psf live load, 10 psf dead load, No. 2 grade, wet service, L/360 deflection); the 18 ft joist limit; the overhang limit of a quarter of the span; the 2 × 8 minimum for a ledger; how a span is measured; joists hung from the ledger or beam on hangers at least 60% of the ledger or beam depth.
    -   Deck beam calculator (DCA 6: Prescriptive Residential Wood Deck Construction Guide (2015), Table 3A and Beam Size & Assembly Requirements): Every beam span in the table (40 psf live load, 10 psf dead load, No. 2 grade, wet service, L/360 deflection), read under the joist-span column at or above the actual joist span; a beam may extend past a post by up to a quarter of its span; beam depth must match or exceed joist depth where joists hang from its side.
    -   Deck footing calculator (DCA 6: Prescriptive Residential Wood Deck Construction Guide (2015), Table 4, Footings, Post Requirements and Commentary Table C4B): Every footing diameter, square size and thickness (40 psf live load, 10 psf dead load, quarter-span overhangs on beam and joists, 150 pcf concrete of 2,500 psi), at 1,500 psf soil in Table 4 and at 2,000, 2,500 and 3,000 psf in Table C4B; the 6 × 6 post heights by species; the 0.9 factor for corner posts; footings at least 12 inches below undisturbed ground or below the frost line; footings within 5 ft of the house bearing at the house footing's elevation; posts 6 × 6 or larger and 8 × 8 posts to 14 ft.
    -   Deck screw calculator (DCA 6: Prescriptive Residential Wood Deck Construction Guide (2015), Decking Requirements): Wood decking is attached to each joist with two 8d threaded nails or two #8 screws, and boards are gapped about 1/8 inch.
    -   Deck stair calculator (DCA 6: Prescriptive Residential Wood Deck Construction Guide (2015), Stair and Stair Handrail Requirements, Figures 27 to 33 and Table 6): The 7-3/4 inch maximum riser, 10 inch minimum tread, 3/8 inch variation limit and 3/4 to 1-1/4 inch nosing; 36 inch minimum width; 2 × 12 stringers, three cut stringers minimum at 18 inches apart or solid stringers at 36 inches; cut stringers spanning 6 ft and solid 13 ft 3 in; a landing above a 12 ft rise; a guard from a 30 inch rise; a handrail from 4 risers; two #8 screws or 8d nails per tread at each stringer and four per 2 × 4 cleat on solid stringers; tread sizes by species.
    -   Deck railing calculator (DCA 6: Prescriptive Residential Wood Deck Construction Guide (2015), Guard Requirements, Guard Post Attachments and Figure 24): A guard on any deck more than 30 inches above grade; the example guard with 4 × 4 posts at 6 ft maximum spacing, a 36 inch minimum height, 2 × 2 balusters, openings that will not pass a 4 inch sphere, 2 × 4 top and bottom rails, a 2 × 6 or 5/4 cap, and the fastener schedule for each; posts through-bolted with two 1/2 inch bolts to a joist or rim joist of at least 2 × 8, with hold-down anchors of 1,800 lb allowable tension for a guard up to 36 inches high.
-   **TimberTech (The AZEK Company)**, [TimberTech Composite and Specialty Decking Installation & Maintenance Guide (rev. 09/23)](https://assets.timbertech.com/content/dam/wp-content/TimberTech-Composite-Installation-Guide-ENG.pdf)
    -   Deck lumber calculator: The default 10% waste allowance: the guide recommends adding roughly 10% to the board count as a scrap factor.
    -   Deck screw calculator: Two screws per joist including end joints when face-screwing; one hidden clip and screw at each joist, each board end at a butt joint with its own clip; the first and last boards fastened along their outer edge at each framing support; its clip box includes the screws.
-   **Fine Homebuilding**, [Decking Installation Overview](https://www.finehomebuilding.com/project-guides/decks/decking-installation-overview)
    -   Deck lumber calculator: About 10% waste and error for boards laid straight, and 15% for boards laid at a 45-degree angle.
-   **Decks.com (Trex Company)**, [Deck board and materials calculator](https://www.decks.com/calculators/decking-calculator/)
    -   Deck lumber calculator: Corroborates the 10% and 15% allowances, and puts complex patterns such as herringbone at up to 20% waste.
-   **Trex Company**, [How Many Deck Boards Do I Need? (2023)](https://www.trex.com/deck-ideas/how-many-deck-boards-do-i-need-/)
    -   Deck lumber calculator: The 5% waste rule of thumb some manufacturer guides use, and its 12 × 12 ft counts (27 boards at 12 ft, 21 at 16 ft), which the deck-size pages reconcile with the 10% figure here.
-   **American Lumber Standard Committee**, [American Softwood Lumber Standard, Voluntary Product Standard PS 20](https://alsc.org/lumber-additional-documents-ps-20/)
    -   Deck lumber calculator: Actual sizes of nominal lumber: a 2 × 6 is 1.5 by 5.5 inches, a 2 × 4 is 1.5 by 3.5 inches, a 2 × 8 is 1.5 by 7.25 inches.
-   **International Code Council**, [2021 International Residential Code, Section R311.7 (stairways)](https://codes.iccsafe.org/content/IRC2021P2/chapter-3-building-planning)
    -   Deck stair calculator: The code section the guide cites for stair width, riser height, tread depth (measured from the face of one riser to the next) and handrails. Local amendments can differ, so check your building department.
    -   Deck railing calculator (2021 International Residential Code, Section R312.1 (guards)): The code section the guide cites for when a guard is required, its height and its openings. Local amendments can differ, so check your building department.

## What this site is not

It is not a structural design service and not a price list. The spans and limits it quotes are the prescriptive tables a typical residential deck is built to; your building department's amendments and an engineer's design take precedence wherever they differ.

Last reviewed November 16, 2026. Built and checked by [Hassan Razeen](https://decktally.com/about/#maintainer).

```json
{"@context":"https://schema.org","@type":"WebPage","@id":"https://decktally.com/methodology/#webpage","name":"Methodology and Sources – DeckTally","url":"https://decktally.com/methodology/","description":"How every DeckTally number is computed, tested and checked, who checks it, and the full list of codes, guides and standards the calculators cite.","inLanguage":"en","datePublished":"2026-10-27","dateModified":"2026-11-16","isPartOf":{"@id":"https://decktally.com/#website"},"author":{"@id":"https://decktally.com/#maintainer"},"breadcrumb":{"@id":"https://decktally.com/methodology/#breadcrumb"}}
{"@context":"https://schema.org","@type":"BreadcrumbList","@id":"https://decktally.com/methodology/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https://decktally.com/"},{"@type":"ListItem","position":2,"name":"Methodology","item":"https://decktally.com/methodology/"}]}
```
