Deck Screw Calculator
To count deck screws, multiply the rows of boards by the number of joists to get the crossings, then allow 2 screws at each one; for hidden fasteners allow 1 clip per joist in each joint between boards and screw the first and last boards at each joist. A 16 × 12 ft deck with 5.5-inch boards and a 0.25-inch gap on joists 16 inches apart has 26 rows of boards crossing 13 joists, so it needs 676 screws face-fastened, or 325 hidden clips plus 26 screws for the first and last boards.
Your materials
Results update as you type.
- Deck screws
- 676 screws
- Hidden clips
- 0 clips
- Screws to buy
- 676 screws
- No extra added
How it adds up
-
Board-and-joist crossings 338 crossings
12 ft of deck width ÷ (5.5 in board + 0.25 in gap) = 26 rows 16 ft of deck length ÷ 16 in spacing, plus one = 13 joists 26 rows × 13 joists = 338
-
Deck screws 676 screws
338 crossings × 2 screws per crossing = 676
-
Hidden clips 0 clips
None: the boards are screwed through the face.
-
Screws to buy 676 screws
676 screws + 0 clips = 676
-
Screws per square foot 3.5
676 ÷ 192 sq ft
-
Boxes —
Enter the fasteners per box to see how many boxes to buy.
Estimates only. Results come from the formulas listed below and use no outside data. Check local building codes and your supplier before buying.
What do I need to enter?
- The deck length (the side the boards run along) and width, the actual board width and the gap, and the joist spacing, exactly as in the lumber calculator.
- Whether the boards are screwed through the face or held by hidden clips in a groove.
- An extra percentage for dropped and stripped fasteners, if you want one.
- How many fasteners come in the box you plan to buy, to get a box count.
How many screws does each board take?
- Crossings: rows of boards × joists. Each is a place a board sits on a joist.
- Deck screws: crossings × 2. The American Wood Council's deck guide and TimberTech fasten each board to each joist with two screws, and Trex recommends the same.
- Hidden clips: one per joist in every joint between boards, so (rows − 1) × joists, each clip with its own screw.
- Edge fasteners: with hidden clips the first and last boards still need one fastener per joist: an edge screw in TimberTech's system, a starter clip and a screw-and-plug in Trex's.
- To buy: screws plus clips, raised by the extra percentage and rounded up; boxes are that number divided by the box size, rounded up.
Assumptions
- Rows and joists are counted exactly as the deck lumber calculator counts them: the deck width divided by one board plus one gap, rounded up, and the deck length divided by the spacing, rounded up, plus one. Boards run straight across the joists.
- Face fastening uses 2 screws per crossing, which the American Wood Council's deck guide and TimberTech specify and Trex recommends. Butt joints where two boards meet on a joist take two more screws each and are not counted.
- Hidden fastening puts 1 clip, with its own screw, at every joist in every joint between boards, so a deck with 26 rows has 25 joints and 325 clips. The first and last boards are counted as one fastener per joist each: TimberTech screws their outer edge at every joist, while Trex starts the first board on a starter clip and finishes the last with a screw and plug. Board ends at butt joints need a clip each and are not counted.
- The guides give no allowance for dropped or stripped fasteners, so the extra field starts at 0%. Boxes are counted from the number you enter, rounded up.
Worked example
A 16 × 12 ft deck, 5.5-inch boards with a 0.25-inch gap, joists at 16 inches, face-screwed:
- Board-and-joist crossings: 338 crossings 12 ft of deck width ÷ (5.5 in board + 0.25 in gap) = 26 rows 16 ft of deck length ÷ 16 in spacing, plus one = 13 joists 26 rows × 13 joists = 338
- Deck screws: 676 screws 338 crossings × 2 screws per crossing = 676
- Hidden clips: 0 clips None: the boards are screwed through the face.
- Screws to buy: 676 screws 676 screws + 0 clips = 676
- Screws per square foot: 3.5 676 ÷ 192 sq ft
What does this calculator leave out?
- Diagonal and herringbone layouts, which cross more joists per board.
- Butt joints where two board ends share a joist: two more screws at each.
- Picture-frame borders, fascia and railing fasteners. Stair tread fasteners are on the deck stair calculator.
- Screw length and coating: the board maker's guide and your local code decide those.
- Framing fasteners: joist hangers are on the deck joist calculator.
FAQ
How many screws per deck board?
Two at every joist the board crosses. The American Wood Council's deck guide attaches wood decking to each joist with two #8 screws or two 8d threaded nails, TimberTech specifies two screws per joist for its boards, and Trex recommends the same. A 16 ft board on joists 16 inches apart crosses 13 joists, so it takes 26 screws.
How many deck screws per square foot?
About 3.5 with 5.5-inch boards and a 0.25-inch gap on joists 16 inches apart: the 16 × 12 ft example has 676 screws over 192 sq ft. Joists at 12 inches raise it to about 4.6 and 24 inches lower it to about 2.4, because the screws go wherever a board crosses a joist.
How many screws do I need for a 12×12 deck?
520 screws with 5.5-inch boards and a 0.25-inch gap on joists 16 inches apart: 26 rows × 10 joists × 2 = 520. With hidden clips it is 250 clips (25 joints × 10 joists) plus 20 screws for the first and last boards.
What screws should I use for decking?
For wood decking the American Wood Council's guide specifies #8 screws or 8d threaded nails, two per joist. For composite boards use the screws or hidden-fastener system the board maker approves: Trex and TimberTech each name their own, and the count on this page is the same either way. This calculator counts fasteners; it does not choose a length or a coating.
The deck lumber calculator counts the boards and joists these fasteners go into, and the board-count guide gives the screw count for nine common deck sizes.
Sources
The counts are arithmetic. The fastening rules come from these publications. Follow them and your local building code over this page where they differ.
- DCA 6: Prescriptive Residential Wood Deck Construction Guide (2015), Decking Requirements, American Wood Council. Wood decking is attached to each joist with two 8d threaded nails or two #8 screws, and boards are gapped about 1/8 inch.
- Trex Decking Installation Guide (2022), Trex Company. Recommends two screws per joist when face-screwing composite boards; requires hidden fasteners at every joist; starts the first board on a starter clip and suggests a hidden-fastener screw and plug for the last board.
- TimberTech Composite and Specialty Decking Installation & Maintenance Guide (rev. 09/23), TimberTech (The AZEK Company). Two screws per joist including end joints when face-screwing; one hidden clip and screw at each joist, each board end at a butt joint with its own clip; the first and last boards fastened along their outer edge at each framing support; its clip box includes the screws.
Every publication the site cites is listed on the methodology page, with how the numbers are computed and checked. Found a mistake? Send a correction. The About page explains who runs DeckTally.
More deck calculators
- Deck materials list
One list for the whole deck: decking, joists, beam, posts, footings and screws.
- Deck lumber calculator
Deck lumber and wood: boards, joists and screws for a rectangular deck, with optional cost.
- Deck joist calculator
Joist count, span check against the AWC table, hangers and rim joists.
- Deck beam calculator
Allowable beam span from the AWC table and the posts a beam needs.
- Deck footing calculator
Footing size, thickness and concrete from the AWC table, with the tallest post.
- Deck stair calculator
Risers, treads, stringer length and count, with the code limits checked.
- Deck railing calculator
Posts, balusters, rails, cap and fasteners, with the gap checked.
- Deck cost calculator
Boards, joists and screws priced with your own numbers.
- Deck stain calculator
Gallons and cans from the coverage on your can.
Last reviewed . Built and checked by Hassan Razeen.