Deck Stair Stringer Calculator

To lay out deck stairs, divide the total rise by the 7.75-inch maximum riser and round up to get the number of risers, divide the rise by that number for the riser height, multiply one fewer treads by the run to get the total run, and take the diagonal of rise and run for the stringer length. A 36-inch rise with a 10-inch run takes 5 risers of 7.2 inches and 4 treads, runs out 3 ft 4 in, and needs 3 stringers (2 × 12, 4 ft 6 in long), 8 tread boards and 24 screws.

Units

Deck surface to the ground or landing, measured plumb.

36 in minimum.

Tread depth, riser face to riser face. 10 in minimum.

Two 5.5-inch boards make an 11-inch tread.

Actual thickness of the tread boards: 1.5 in for 2× lumber.

Your materials

Results update as you type.

Risers
5 risers
7.2 in (≈ 7 3/16 in) each
Total run
3 ft 4 in
Within the 6 ft stringer span
Stringers
3 stringers
2 × 12, 4 ft 6 in long

How it adds up

  1. Risers 5 risers

    36 in rise ÷ 7.75 in maximum = 4.65, rounded up to 5 36 in ÷ 5 = 7.2 in (≈ 7 3/16 in) per riser

  2. Treads 4 treads

    5 risers − 1 = 4: the deck itself is the top step

  3. Total run 3 ft 4 in

    4 treads × 10 in = 3 ft 4 in DCA 6 Figure 28 allows a cut stringer to span 6 ft

  4. Stringers 3 stringers

    Cut stringers at most 18 in apart across 36 in, and never fewer than 3 = 3 Length: √(36 in² + 40 in²) = 4 ft 5.81 in, so 4 ft 6 in of stock before any extra for the top and bottom cuts

  5. Stringer layout 35.8° pitch

    Each notch: 7.2 in (≈ 7 3/16 in) rise by 10 in run Pitch: tan⁻¹(7.2 in ÷ 10 in) = 35.8° Bottom cut: 7.2 in riser − 1.5 in tread = 5.7 in (≈ 5 11/16 in), so the first step finishes as tall as the rest

  6. Tread boards 8 boards

    4 treads × 2 boards = 8 8 × 3 ft = 24 ft

  7. Tread fasteners 24 screws

    4 treads × 3 stringers × 2 #8 screws or 8d nails = 24

  8. Code checks Pass

    Run of 10 in meets the 10 in minimum. Width of 36 in meets the 36 in minimum. A stair guard is required: the rise is 30 in or more. A handrail is required on at least one side: 4 or more risers.

Estimates only. Results come from the formulas listed below and use no outside data. Check local building codes and your supplier before buying.

Your stair, from the side

Side view of a stair rising 36 in over a run of 3 ft 4 in, with 5 risers and 4 treads. Total rise 36 in Total run 3 ft 4 in
  • 5 risers of 7.2 in (≈ 7 3/16 in)
  • 4 treads, 10 in run each
  • Stringer 4 ft 6 in at 35.8°, first notch 5.7 in (≈ 5 11/16 in) up
Embed this calculator on your site

Paste this where you want the calculator. It is free, shows no ads, works in any site, and links back to this page. Change the height to suit your layout.

What do I need to measure for deck stairs?

  1. The total rise: from the finished deck surface straight down to where the stair will land. Measure it, do not estimate it.
  2. How wide the stair will be, 36 inches at least.
  3. The run of each step, from one riser face to the next; 10 inches is the minimum and two 5.5-inch boards with a nosing give about 10.5.
  4. Cut stringers, notched for each step, or solid stringers with the treads on cleats between them.
  5. How many boards make up each tread, and how thick they are: the stringer's bottom is cut shorter by that thickness.

How do I calculate stair stringers, risers and treads?

Assumptions

Worked example

A 36-inch rise, 36 inches wide, 10-inch run, cut stringers, 2 boards per tread, each 1.5 inches thick:

What are the code requirements for deck stairs?

The limits the calculator checks, from the American Wood Council's deck guide, which cites IRC R311.7. Your local code may amend them.

What does this calculator leave out?

FAQ

How many steps do I need for a 3 ft (36-inch) high deck?

5 risers and 4 treads: 36 ÷ 7.75 = 4.65, rounded up to 5, so each riser is 7.2 inches. A 30-inch deck takes 4 risers of 7.5 inches, a 48-inch deck 7 of 6.86 inches, and a 60-inch deck 8 of 7.5 inches.

What is the maximum riser height for deck stairs?

7.75 inches, with no riser differing from another by more than 0.38 inch, under the American Wood Council's deck guide and IRC R311.7. The tread must run at least 10 inches, measured as the IRC measures tread depth, from the face of one riser to the next, with a nosing of 0.75 to 1.25 inch, and an open riser may not pass a 4-inch sphere.

How long should stair stringers be?

The diagonal of the total rise and the total run: for the 36-inch example, √(36² + 40²) = 4 ft 5.81 in, so 4 ft 6 in of stock before the cuts at the top and bottom. A 48-inch rise with an 11-inch run gives 7 risers, a 5 ft 6 in run and a 6 ft 10 in stringer. Stringers must be 2 × 12, and a cut stringer may span only 6 ft horizontally, a solid one 13 ft 3 in, before it needs a post or a landing.

How do I lay out and cut a stair stringer?

Mark the riser height on one arm of a framing square and the run on the other, then step the square down a 2 × 12 once for each tread. For the 36-inch example each notch is 7.2 inches (about 7 3/16 in) of rise by 10 inches of run. Cut the bottom of the stringer shorter by the tread thickness: 7.2 − 1.5 = 5.7 inches (about 5 11/16 in) from the landing to the first notch, so the first finished step matches the rest. A cut stringer must keep at least 5 inches of wood below the notches.

What angle are deck stairs?

The angle whose tangent is the riser height over the run. The 36-inch example, with 7.2-inch risers and a 10-inch run, is pitched at 35.8°. The steepest stair the limits allow, a 7.75-inch riser over a 10-inch run, is 37.8°; a deeper run makes it shallower, and a 48-inch rise with an 11-inch run comes to 31.9°.

How many stringers do deck stairs need?

At least 3 cut stringers, spaced no more than 18 inches apart, so a 36-inch stair takes 3 and a 48-inch stair takes 4. Solid stringers carrying the treads on 2 × 4 cleats may be 36 inches apart, so a 36-inch stair takes 2, but the guide's Table 6 then asks for thicker treads: 2 × 8 for Southern Pine; 2 × 8 or 3 × 4 for Douglas Fir-Larch, Hem-Fir, Spruce-Pine-Fir; 2 × 10 or 3 × 4 for Redwood, Western Cedars, Ponderosa Pine, Red Pine. On cut stringers any group may use 2 × 4 or 5/4 boards.

How wide do deck stairs have to be?

At least 36 inches, and any landing at least as wide as the stair and 36 inches in the direction of travel. A rise of more than 12 ft needs an intermediate landing.

Do deck stairs need a handrail or a guard?

A handrail on at least one side once there are 4 or more risers, 34 to 38 inches above the tread nosings, and a stair guard once the total rise is 30 inches or more. The guide gives that threshold twice: its stair figure (Figure 30) says a total rise of 30 inches or more, while its Guard Requirements and IRC R312.1.1 say more than 30 inches above grade, so at exactly 30 inches ask your building department. The 36-inch example needs both; a 30-inch rise with 4 risers needs a guard and a handrail.

The deck joist calculator frames the deck these stairs lead to, and the deck screw calculator counts the fasteners for its boards.

Sources

The counts are arithmetic. Every limit on this page comes from these publications. Follow them and your local building code over this page where they differ.

Every publication the site cites is listed on the methodology page, with how the numbers are computed and checked. Found a mistake? Send a correction. The About page explains who runs DeckTally.

More deck calculators

Last reviewed . Built and checked by Hassan Razeen.